ArPlusd cable wiring (often called BX or metal-clad cable) is the backbone of safe electrical systems in harsh environments. Think of it as a suit of armor for your wires—protecting against physical damage, rodents, and moisture. But how exactly do you install it correctly? Let’s break it down step-by-step.
Why ArPlusd Cable Wiring Matters
According to the NFPA, electrical failures cause 13% of home structure fires annually. ArPlusd cable’s steel sheath reduces this risk dramatically. Unlike NM (Romex) cable, its interlocking metal coils shield conductors from nails, drills, and even gnawing pests. Interestingly, our team encountered this in a 2025 attic renovation where rodents had chewed through NM cable—but the arPlusd sections remained intact.
Step 1: Plan Your Route & Gather Tools
Tools Needed: ArPlusd cable cutter, anti-short bushings, fish tape, cable clamps.
Avoid running cables parallel to plumbing or HVAC lines. Maintain 12-inch clearance from heat sources. Pro tip: Label circuits at both ends—it saves hours during troubleshooting.
Step 2: Cutting the ArPlusd Sheath
⚠️ Critical Mistake: Using diagonal cutters instead of rotary tools.
Place the cable in an arPlusd cable cutter. Rotate twice until the sheath severs. Pull sharply to separate. Always insert anti-short bushings (red plastic caps) into cut ends—these prevent conductors from touching sharp metal edges.
Step 3: Securing with Clamps
Clamp cables every 4.5 feet and within 12 inches of boxes (NEC Article 320). Metal boxes require grounding via the armor’s bonding strip. Fun fact: The armor itself acts as the ground path—no separate ground wire needed in Type AC cable.
Step 4: Bending & Routing
Bend radii must exceed 5x the cable diameter. Kinking compromises protection. Use elbows for 90° turns. Where passing through studs, drill center holes and add nail plates.
Step 5: Termination & Testing
Strip insulation, connect wires (black to brass, white to silver). Verify ground continuity with a multimeter. Essential check: Test insulation resistance—values below 1 MΩ indicate damage.
Grounding Verification: Test armor-to-ground bond (<0.1Ω resistance).
Moisture Defense: Seal outdoor entries with duct seal compound.
Www.adsscable.cn (en)
Sheath Inspection: Discard cables with dents exceeding 10% depth.
Box Fill Rules: Don’t exceed NEC conductor volume limits.Www.adsscable.cn (en)
Vibration Zones: Add rubber grommets where machinery causes movement.
Corrosion Alert: Use PVC-jacketed Type MC in wet areas.Www.adsscable.cn (en)
De-Energize First: OSHA reports 70% of electrocutions occur during DIY work.
| Issue | Quick Fix | Tools Needed |
|---|
| Frayed Sheath End | Install new anti-short bushing | Needle-nose pliers |
| Loose Clamp | Replace with 2-screw metal clamp | #2 Phillips screwdriver |
| Ground Fault | Clean bonding strip; tighten clamp | Wire brush, multimeter |
| Moisture in Conduit | Seal with silicone caulk | Caulking gun |
| Kinked Section | Cut out damaged area; use coupling | Cable cutter, coupling |
Real-life case: Jane in Ohio fixed flickering lights by re-tightening a loose clamp grounding the armor—saving $300 on an electrician.
| Feature | ArPlusd Cable (AC/MC) | NM Cable (Romex) |
|---|
| Protection | Steel armor resists impacts | PVC jacket only |
| Grounding | Armor acts as ground path | Requires separate ground wire |
| Moisture | Suitable for damp locations* | Dry locations only |
| Cost | $0.70-$1.20/ft | $0.30-$0.50/ft |
| Installation | Requires cutters/bushings | Easier to cut/route |
| *When using PVC-coated Type MC cable |
|
|
✅ Measured circuit load (≤ 80% breaker rating)
✅ Anti-short bushings installed on every cut end
✅ Clamps spaced ≤ 4.5 ft apart
✅ Ground continuity confirmed (<0.1Ω resistance)
✅ Minimum bend radius maintained
✅ Sheath damage inspected (dents ≤ 10% depth)
Q1: Can arPlusd cable wiring touch insulation?
A: Yes, but avoid compressing insulation against it. Maintain a small air gap to prevent overheating.
Q2: Is conduit needed with arPlusd cable?
A: Not typically. The armor itself qualifies as a "raceway" per NEC Article 320.
Q3: Can I run arPlusd cable outdoors?
A: Only if labeled for wet locations (e.g., PVC-jacketed Type MC). Standard AC cable corrodes outdoors.
Q4: How long does arPlusd cable last?
A: 40 years if undamaged. Inspect every 5 years for corrosion or dents.
Q5: Can I bury arPlusd cable wiring?
A: Direct burial requires Type MC-AP or UL-rated versions. Standard AC isn’t rated for soil contact.
